OEE Calculator for Plastics and Injection Moulding
For injection moulding, blow moulding and extrusion lines, where cycle time and mould changes decide OEE.
This calculator needs JavaScript. You can still read how the numbers are worked out below, including a worked example.
Your numbers
Updates as you typeYour result
Free, no sign-upGet your full OEE loss report
Your results as a PDF, the six big losses broken down, plus our free OEE Loss Tracker (Excel) to log every shift and machine.
- Your result above stays free. You never need to sign up to calculate.
Your report is on its way.
Want help reading it?
Book a 30-minute OEE review with our teamWe've also emailed you the links.
How this OEE calculator works for Plastics
OEE (overall equipment effectiveness) is the share of planned production time that produced good mouldings at full speed. It multiplies availability (run time ÷ planned production time), performance (ideal cycle time × total count ÷ run time) and quality (good count ÷ total count). Planned production time is the shift length minus planned stops. The general explanation is on the OEE calculator page.
OEE = Availability × Performance × Quality
Worked example
A moulder runs a 4-cavity mould on a 250-tonne machine for an 8-hour shift. Counts are in shots. In the calculator above this is the starting example: a shift of 480 minutes with 30 minutes of planned stops, so planned production time is 450 minutes. Downtime takes 60 minutes, so run time is 390 minutes. The ideal cycle time is 32 seconds (0.53 minutes) per moulding. The line makes 600 mouldings, of which 579 are good.
| Factor | Calculation | Result |
|---|---|---|
| Availability | 390 ÷ 450 | 86.7% |
| Performance | (0.53 min × 600) ÷ 390 | 82.1% |
| Quality | 579 ÷ 600 | 96.5% |
| OEE | 86.7% × 82.1% × 96.5% | 68.6% |
The losses that matter in Plastics
In moulding the cycle is long and fixed by the mould, so the big performance loss is cycle time creeping above the design value, and the big availability loss is mould change and start-up.
| Loss in Plastics | Counted in | What it looks like |
|---|---|---|
| Mould change and colour change | Availability | Machine stopped to change the mould, purge or change colour or material |
| Machine and auxiliary breakdowns | Availability | Hydraulics, heaters, chillers, robots or dryers stopping the cell |
| Cycle time above design | Performance | Longer cooling, slower ejection or conservative settings |
| Short stops | Performance | Part-pick faults, flash clearing and sensor trips |
| Start-up scrap | Quality | Shots rejected until the process is stable after a stop or change |
| Defect rejects | Quality | Short shots, sinks, flash or colour faults |
Measuring OEE properly in Plastics
Use the mould’s design cycle time as the ideal, and count the same unit throughout: either shots or parts, not a mix. Cycle time variation is the main source of performance loss in moulding, so a single average cycle time can hide it; look at the real cycle times, not only the setting. Count start-up scrap as a quality loss. Regrind that goes back into the process is not a good part.
What do published figures say about OEE in Plastics?
Published ranges for plastics come from a vendor that groups it with packaging:
- TeepTrak reports 50–65% as typical for plastics and packaging in India, with 75% or more as world class. TeepTrak India benchmark
- TeepTrak does not disclose its sample size, data source or calculation method.
For reference, the widely quoted 85% comes from Seiichi Nakajima's 1984 book on total productive maintenance as a minimum to strive for (90% availability, 95% performance, 99% quality), and oee.com notes it was set for discrete manufacturing. Across industries, Evocon's data from more than 3,500 machines puts the typical plant nearer 55–60%. There is no audited benchmark for any single industry, so judge your line against its own trend and keep the definitions the same each time.
How maintenance software helps
- Track each mould as an asset, with shots counted and maintenance due by shots, not by calendar date.
- Schedule preventive maintenance on hydraulics, heaters, chillers and dryers during mould-change windows.
- Record every stop with a cause code so mould change, material problems and machine faults are ranked separately.
More for Plastics
- Maintenance software for Plastics
- Preventive maintenance schedule for Plastics, rubber & polymers
- OEE software
- Downtime cost calculator
- MTTR and MTBF calculator
- OEE calculator
OEE calculators for other industries
Not your industry? Pick another one below, or search at the top of the page.
Process plants: continuous and batch How it is calculated
- CementCement, glass, ceramics & building materials
- Steel and MetalsSteel, foundry, forging & metals
- MiningMining & mineral processing
- Oil and GasOil, gas & refining
- Chemicals and FertilisersChemicals, fertilisers & petrochemicals
- Paper and PulpPaper, pulp & board
- Sugar and DistilleriesAgro, grain, edible oil & sugar
- DairyFood, dairy & beverage processing
- Food ProcessingFood, dairy & beverage processing
- API and Bulk DrugsAPI & bulk drugs
- TextileTextile & garments
Production lines: parts, packs and units How it is calculated
- Auto ComponentsAutomotive & auto components
- ElectronicsElectronics & electrical manufacturing
- FMCGFMCG & consumer goods
- PackagingPackaging, paper & printing
- Tyre and RubberTyre & rubber
- PharmaceuticalPharmaceutical & biotech
Is your industry or kind of plant missing? Tell us what to add and we will look at building a calculator for it.