OEE Calculator for Electronics Manufacturing
For SMT, PCB assembly and test lines, where short stops and changeovers decide the result.
This calculator needs JavaScript. You can still read how the numbers are worked out below, including a worked example.
Your numbers
Updates as you typeYour result
Free, no sign-upGet your full OEE loss report
Your results as a PDF, the six big losses broken down, plus our free OEE Loss Tracker (Excel) to log every shift and machine.
- Your result above stays free. You never need to sign up to calculate.
Your report is on its way.
Want help reading it?
Book a 30-minute OEE review with our teamWe've also emailed you the links.
How this OEE calculator works for Electronics
OEE (overall equipment effectiveness) is the share of planned production time that produced good boards at full speed. It multiplies availability (run time ÷ planned production time), performance (ideal cycle time × total count ÷ run time) and quality (good count ÷ total count). Planned production time is the shift length minus planned stops. The general explanation is on the OEE calculator page.
OEE = Availability × Performance × Quality
Worked example
An EMS plant runs an SMT line building a control board on an 8-hour shift. In the calculator above this is the starting example: a shift of 480 minutes with 40 minutes of planned stops, so planned production time is 440 minutes. Downtime takes 55 minutes, so run time is 385 minutes. The ideal cycle time is 36 seconds (0.6 minutes) per board. The line makes 540 boards, of which 511 are good.
| Factor | Calculation | Result |
|---|---|---|
| Availability | 385 ÷ 440 | 87.5% |
| Performance | (0.6 min × 540) ÷ 385 | 84.2% |
| Quality | 511 ÷ 540 | 94.6% |
| OEE | 87.5% × 84.2% × 94.6% | 69.7% |
The losses that matter in Electronics
In electronics the line moves at the pace of its slowest machine, and the losses are often many small stops rather than a few long ones.
| Loss in Electronics | Counted in | What it looks like |
|---|---|---|
| Reel and feeder changes | Availability | Waiting for the next component reel or a feeder fault to be cleared |
| Programme and product changeover | Availability | Line stopped while stencil, programme and feeders are set for the next board |
| Nozzle and pick-up errors | Performance | Short stops that the machine clears itself but that cut the real rate |
| Waiting for the next station | Performance | The slowest station starved or blocked by its neighbours |
| Solder and placement defects | Quality | Boards that fail inspection and go to repair |
| Test failures and rework | Quality | Boards that only pass the second time |
Measuring OEE properly in Electronics
Measure OEE on the machine that sets the pace of the line (the bottleneck), not on every machine in turn and then averaging. Take the ideal cycle time from the machine’s rated placement speed for the board, and count a board as good only if it passes inspection and test first time. Repaired boards are a quality loss. Semiconductor fabrication has its own standard for equipment productivity, SEMI E79, which this calculator does not replace.
What do published figures say about OEE in Electronics?
For electronics assembly the published numbers vary a lot and come from vendors:
- TeepTrak reports 50–68% as typical for SMT and PCB assembly in India, with 78% or more as world class. TeepTrak India benchmark
- TeepTrak does not disclose its sample size, data source or calculation method.
- For semiconductor equipment, SEMI E79 defines how equipment productivity and OEE are measured. SEMI E79
For reference, the widely quoted 85% comes from Seiichi Nakajima's 1984 book on total productive maintenance as a minimum to strive for (90% availability, 95% performance, 99% quality), and oee.com notes it was set for discrete manufacturing. Across industries, Evocon's data from more than 3,500 machines puts the typical plant nearer 55–60%. There is no audited benchmark for any single industry, so judge your line against its own trend and keep the definitions the same each time.
How maintenance software helps
- Log every line stop with a cause code (feeder, nozzle, conveyor, oven), so the many small stops become visible and can be ranked.
- Plan preventive maintenance of placement heads, nozzles, ovens and conveyors in the changeover windows, not in the middle of a run.
- Track calibration of inspection and test equipment, so a drifting instrument does not create false failures.
More for Electronics
- Maintenance software for Electronics
- Preventive maintenance schedule for Electronics & electrical manufacturing
- OEE software
- Downtime cost calculator
- MTTR and MTBF calculator
- OEE calculator
OEE calculators for other industries
Not your industry? Pick another one below, or search at the top of the page.
Process plants: continuous and batch How it is calculated
- CementCement, glass, ceramics & building materials
- Steel and MetalsSteel, foundry, forging & metals
- MiningMining & mineral processing
- Oil and GasOil, gas & refining
- Chemicals and FertilisersChemicals, fertilisers & petrochemicals
- Paper and PulpPaper, pulp & board
- Sugar and DistilleriesAgro, grain, edible oil & sugar
- DairyFood, dairy & beverage processing
- Food ProcessingFood, dairy & beverage processing
- API and Bulk DrugsAPI & bulk drugs
- TextileTextile & garments
Production lines: parts, packs and units How it is calculated
- Auto ComponentsAutomotive & auto components
- FMCGFMCG & consumer goods
- PackagingPackaging, paper & printing
- PlasticsPlastics, rubber & polymers
- Tyre and RubberTyre & rubber
- PharmaceuticalPharmaceutical & biotech
Is your industry or kind of plant missing? Tell us what to add and we will look at building a calculator for it.