OEE Calculator for Dairy Plants
For milk reception, pasteurising, separating and packing lines, with CIP built into the day.
This calculator needs JavaScript. You can still read how the numbers are worked out below, including a worked example.
Your numbers
Updates as you typeYour result
Free, no sign-upGet your full OEE loss report
Your results as a PDF, with the on-stream factor and TEEP, plus our free OEE Loss Tracker (Excel) to log every period and line.
- Your result above stays free. You never need to sign up to calculate.
Your report is on its way.
Want help reading it?
Book a 30-minute OEE review with our teamWe've also emailed you the links.
How this OEE calculator works for Dairy
OEE (overall equipment effectiveness) is the share of what a pasteurising and packing line could have made at its rated rate, in the time it was planned to run, that came out right first time. It multiplies availability (run time ÷ planned production time), performance (actual rate while running ÷ rated rate) and quality (on-spec output ÷ total output). Planned shutdowns are left out of planned production time. The full method, including how to choose the rated rate and how batch plants are handled, is on the OEE calculator for process industries page.
OEE = Availability × Performance × Quality
Worked example
A dairy runs a pasteurising and packing line over a 168-hour week with a rated rate of 20,000 litres an hour. In the calculator above this is the starting example: a period of 168 hours with 12 hours of planned shutdown, so planned production time is 156 hours. Unplanned stops take 20 hours, so the plant runs for 136 hours. It makes 2300000 litres of milk, of which 2240000 litres of milk are on-spec, against a rated rate of 20000 litres of milk an hour.
| Factor | Calculation | Result |
|---|---|---|
| Availability | 136 ÷ 156 | 87.2% |
| Performance | (2300000 ÷ 136) ÷ 20000 | 84.6% |
| Quality | 2240000 ÷ 2300000 | 97.4% |
| OEE | 87.2% × 84.6% × 97.4% | 71.8% |
Against the whole 168 hours the plant ran 81.0% of the time (the on-stream factor) and TEEP is 66.7%. The planned shutdown is not an OEE loss, but it shows in these calendar-time figures.
The losses that matter in Dairy
Dairies run clean-in-place (CIP) cycles often, switch between products and handle a perishable raw material. How CIP is treated decides the OEE figure, so the rule matters as much as the maths.
| Loss in Dairy | Counted in | What it looks like |
|---|---|---|
| CIP overruns | Availability | Cleaning that takes longer than the validated cycle |
| Product changeovers | Availability | Flushing and changing between milk, curd, flavoured products or pack sizes |
| Breakdowns of pumps, homogenisers and fillers | Availability | Stops that need a technician or a spare part |
| Filler and packing slow-downs | Performance | Short stops and reduced speed at the packing machine |
| Milk supply and cooling limits | Performance | Line held at reduced rate by milk arrival or chilling capacity |
| Interface and flush losses | Quality | Product lost between one product and the next, or discarded for a fault |
Measuring OEE properly in Dairy
Sources disagree on CIP, and no standard fixes it. A common and defensible rule: a CIP cycle that follows the validated time is a planned stop and left out of planned production time, and any time beyond it is downtime. Another valid rule counts all CIP as downtime. Pick one, write it on the report and keep it consistent. Measure per line, and choose the unit (litres of milk, kilograms of product, or packs) and use it throughout.
What do published figures say about OEE in Dairy?
No audited OEE benchmark for dairies was found. A related reference:
- TeepTrak reports 45–60% as typical for food processing in India, with 70% or more as world class; it does not disclose its sample size, data source or calculation method. TeepTrak India benchmark
- Vendor guides disagree on whether scheduled CIP counts as planned time or as a loss, and one notes that a dairy may classify it either way if it says so on the report.
For reference, the widely quoted 85% comes from Seiichi Nakajima's 1984 book on total productive maintenance as a minimum to strive for (90% availability, 95% performance, 99% quality), and oee.com notes it was set for discrete manufacturing. Across industries, Evocon's data from more than 3,500 machines puts the typical plant nearer 55–60%. There is no audited benchmark for any single industry, so judge your line against its own trend and keep the definitions the same each time.
How maintenance software helps
- Schedule preventive maintenance on pumps, homogenisers, heat exchangers and fillers around the CIP cycles.
- Record every stop with a cause code (CIP overrun, changeover, breakdown, milk shortage), so the avoidable time is clear.
- Keep hygiene-critical items, such as gaskets and seals, in a tracked store and replaced on schedule.
More for Dairy
- Maintenance software for Dairy
- Preventive maintenance schedule for Food, dairy & beverage processing
- OEE software
- Downtime cost calculator
- MTTR and MTBF calculator
- OEE calculator for process industries
OEE calculators for other industries
Not your industry? Pick another one below, or search at the top of the page.
Process plants: continuous and batch How it is calculated
- CementCement, glass, ceramics & building materials
- Steel and MetalsSteel, foundry, forging & metals
- MiningMining & mineral processing
- Oil and GasOil, gas & refining
- Chemicals and FertilisersChemicals, fertilisers & petrochemicals
- Paper and PulpPaper, pulp & board
- Sugar and DistilleriesAgro, grain, edible oil & sugar
- Food ProcessingFood, dairy & beverage processing
- API and Bulk DrugsAPI & bulk drugs
- TextileTextile & garments
Production lines: parts, packs and units How it is calculated
- Auto ComponentsAutomotive & auto components
- ElectronicsElectronics & electrical manufacturing
- FMCGFMCG & consumer goods
- PackagingPackaging, paper & printing
- PlasticsPlastics, rubber & polymers
- Tyre and RubberTyre & rubber
- PharmaceuticalPharmaceutical & biotech
Is your industry or kind of plant missing? Tell us what to add and we will look at building a calculator for it.